One axis AC servo injection manipulator arm BRTP07ISS1PC

One axis servo manipulator BRTP07ISS1PC

Short Description

BRTP07ISS1PC series applies to all types of horizontal injection machines of 60T-200T for take-out products. The up and down arm is a single sectional type.

Main Specification

Recommended I.M.M (ton): 60T-200T

Vertical Stroke (mm): 750

Traverse Stroke (mm): /

Max loading (kg): 2

Weight (kg): 50

Send email to us

Product Detail

Product Tags

10000

Product Introduction

BRTP07ISS1PC series applies to all types of horizontal injection machines of 60T-200T for take-out products. The up and down arm is a single sectional type. The up and down action is driven by AC servo motor, with accurate positioning, fast speed, long service life, and low failure rate. The rest parts are driven by air pressure. It is economical and affordable. After installing this robot, productivity will be increased by 10-30%

Accurate Positioning

Fast

Long Service Life

Low Failure Rate

Reduce Labor

Telecommunication

Basic Parameters

Power Source (KVA)	Recommended I.M.M (ton)	Traverse Driven	Model of EOAT
1.27	60T-200T	AC Servo motor、Cylinder drive	zero suction zero fixture
Traverse Stroke (mm)	Crosswise Stroke (mm)	Vertical Stroke (mm)	Max.loading (kg)
/	125	750	2
Dry Take Out Time (sec)	Dry Cycle Time (sec)	Swing Angle (degree)	Air Consumption (NI/cycle)
1.4	5	/	3
Weight(kg)
50

Model representation: W: Telescopic type. D: Product arm +runner arm. S5: Five-axis driven by AC Servo Motor( Traverse-axis、Vertical-axis + Crosswise-axis).
The above-mentioned cycle time are the results of our company’s internal test standard. In the actual application process of the machine, they will vary according to the actual operation.

Trajectory Chart

A	B	C	D	E	F	G	H
1577	/	523	500	1121	881	107	125
I	J	K
224	45°	90°

No further notice if the specification and appearance are changed due to improvement and other reasons. Thank you for your understanding.

Recommended Industries

FUNCTION

5.1 General function

In the status of STOP and AUTO, Press “FUNC” key to enter Function page, Use up/down key to move to each function, you can press STOP key to leave Function page and return Stop page.

1、Language：Language Selection
2、EjectCtrl：
NotUse：Allow the thimble signal long-term output, Thimble action of injection does not be controled.
Use ：When the robot began to move, Disconnect thimble signal and start timing,. Allow to output thimble signal after thimble delay time.
3、ChkMainFixt：
PositPhase：Positive detected fixture switch. Fixture switch signal will be ON when Fetch success in AUTO mode.
ReverPhase：RP to detect fixture switch. Fixture switch signal will be OFF when Fetch success in AUTO mode.
NotUse：Not detect fixture switch. Not detect switch signal no matter what the Fetching action success or not.
4、ChkViceFixt：The same as Chk ChkMainFixt.
5、ChkVacuum：
Not Use：Not detect vacuum switch signal at Automatic run-time.
Use：Vacuum switch signal will be ON when Fetch success in AUTO mode.

Time Modify

In the Stop or Auto Page, Press TIME key can enter Time Modify page.

Press the cursor keys to each step sequence to modify the time, Press Enter key after input the number, Time changes is finished.
The time behind Action step is delay time before action. Current action will be executed until delay time-out.
If the current step sequence action is the switch to confirm. Action time will be recorded the same. If real action time cost more than the record, then the next action can be continued until action switch confirmed after time-out.