High speed manipulator for mold injection BRTR08TDS5PC, FC

Five axis servo manipulator BRTR08TDS5PC,FC

Short Description

Accurate positioning, high speed, long life, and low failure rate. After installing the manipulator can increase production capacity (10-30%) and will reduce the defective rate of products, ensure the safety of operators, and reduce manpower. Accurately control production, reduce waste and ensure delivery.

Main Specification

Recommended I.M.M (ton): 50T-230T

Vertical Stroke (mm): 810

Traverse Stroke (mm): 1300

Max loading (kg): 3

Weight (kg): 295

Send email to us

Product Detail

Product Tags

28500

Product Introduction

BRTR08TDS5PC/FC series is suitable for 50T-230T horizontal injection molding machine to take out the finished product and nozzle, arm form ternary type, two-arm, five-axis AC servo drive, can be used for quick removal or in-mold sticking, in-mold inserts and other special product applications. Accurate positioning, high speed, long life, and low failure rate. After installing the manipulator can increase production capacity (10-30%) and will reduce the defective rate of products, ensure the safety of operators, and reduce manpower. Accurately control production, reduce waste and ensure delivery. Five-axis driver and controller integrated system: fewer signal lines, long-distance communication, good expansion performance, strong anti-interference ability, high accuracy of repeated positioning, multi-axis can be controlled at the same time, simple equipment maintenance, and low failure rate.

Accurate Positioning

Fast

Long Service Life

Low Failure Rate

Reduce Labor

Telecommunication

Basic Parameters

Power Source (kVA)	Recommended IMM (ton)	Traverse Driven	Model Of EOAT
3.57	50T-230T	AC Servo motor	two suctions two fixtures
Traverse Stroke (mm)	Crosswise Stroke (mm)	Vertical Stroke (mm)	Max Loading (kg)
1300	p:430-R:430	810	3
Dry Take Out Time (sec)	Dry Cycle Time (sec)	Air Consumption (NI/cycle)	Weight (kg)
0.92	4.55	4	295

Model representation: W: Telescopic type. D: Product arm +runner arm. S5: Five-axis driven by AC Servo Motor( Traverse-axis、Vertical-axis + Crosswise-axis).
The above-mentioned cycle time are the results of our company’s internal test standard. In the actual application process of the machine, they will vary according to the actual operation.

Trajectory Chart

A	B	C	D	E	F	G
910	2279	810	476	1300	259	85
H	I	J	K	L	M	N
92	106.5	321.5	430	1045.5	227	430

No further notice if the specification and appearance are changed due to improvement and other reasons. Thank you for your understanding.

Precautions for Robot Operation

1.To guarantee safe machine operation, install external safety circuits and establish a second maintenance path.

2. It is essential to comprehend the contents of the machine handbook prior to setting up the equipment, wiring, operating it, and performing maintenance on the five-axis servo manipulator. When utilizing it, it's also important to be aware of the safety considerations associated to mechanical and electronic expertise.

3. Metal and other flame-resistant materials should be used to mount the five-axis servo robotic arm. Due to the robotic arm's electrical power source, it is especially important to ensure that the equipment's surroundings are free of flammable materials and to remove any possible risks.

4. When using the robot, grounding is required. The robot is a substantial piece of machinery, and grounding can best safeguard users from harm due to accident for their own personal safety.

5. Qualified electricians must carry out the wiring operation for the robotic arm with five axes of servo motion. The wiring is rather disorganized and has to be handled by operators with expert electronic understanding to ensure safe wiring.

6. When operating, operators should take a safe stance and avoid standing directly beneath the manipulators.

Program High-speed

Program High-speed injection manipulator procedure:
1.Set the manipulator to the Auto state in step
2. The manipulator returns to the starting position and awaits the opening of the mold by the injection molding machine.
3. Use sucker 1 to extract the completed item.
4. After recognizing the success of picking, the manipulator produces the close mold permit signal and moves out of the mold range along the X and Y axes.
5. The manipulator positions the final product and material scraps in the appropriate locations.
6. Begin the conveyor to operate for three seconds each time a finished item is put on it.
7. The manipulator goes back to the starting location and waits.