High precision five axis injection molding manipulator arm BRTR11WDS5PC，FC

Five axis servo manipulator BRTR11WDS5PC，FC

Short Description

Accurate positioning, high speed, long life, and low failure rate. After installing the manipulator can increase production capacity (10-30%) and will reduce the defective rate of products, ensure the safety of operators, and reduce manpower.

Main Specification

Recommended I.M.M (ton): 320T-470T

Vertical Stroke (mm): 1100

Traverse Stroke (mm): 1700

Max loading (kg): 10

Weight (kg): 255

Send email to us

Product Detail

Product Tags

28500

Product Introduction

BRTR11WDS5PC/FC series is suitable for 320T-470T horizontal injection molding machine to take out the finished product and nozzle, arm form telescopic type, two-arm, five-axis AC servo drive, can be used for quick removal or in-mold sticking, in-mold inserts and other special product applications, accurate positioning, high speed, long life, low failure, installation manipulator can increase production capacity (10-30%), reduce the defective rate of products, ensure the safety of operators, and reduce manual labor. Accurately control production, reduce waste and ensure delivery.
The integrated control system of five-axis drive and control: less signal lines, long-distance communication, good expansion performance, strong anti-interference ability, high repetitive positioning accuracy, multi-axis can be controlled at the same time, simple equipment maintenance and low failure rate.

Accurate Positioning

Fast

Long Service Life

Low Failure Rate

Reduce Labor

Telecommunication

Basic Parameters

Power Source (kVA)	Recommended I.M.M (ton)	Traverse Driven	Model of EOAT
4.6	320T-470T	AC Servo motor	Four suctions two fixtures
Traverse Stroke (mm)	Crosswise Stroke (mm)	Vertical Stroke (mm)	Max.loading (kg)
1700	P:600-R:600	1100	10
Dry Take Out Time (sec)	Dry Cycle Time (sec)	Air Consumption (NI/cycle)	Weight (kg)
2.49	7.2	4	255

Trajectory Chart

A	B	C	D	E	F	G
1426.5	2342	1100	290	1700	369	165
H	I	J	K	L	M	N
176	106	481	600	1080	286	600

No further notice if the specification and appearance are changed due to improvement and other reasons. Thank you for your understanding.

Rope Lifting Posture

Lifting position: A crane should be used to handle the robot. Prior to carrying and lifting, a lifting rope must be used to securely thread the robot and manage the balancing distance. Only then may handling activities be performed on the robot, including a smooth lift.

Thread the lifting rope through the transverse arch's end from the base side, near to the pulling arm side.
Bind the arch's ends together, then tie the hook. To control the pulling beam, change the balancing condition, hook the pulling end, and avoid overturning, use a lifting rope at the pulling end.
Control the hoisting rope's balance while gradually removing the screws from the foundation hole.
Tighten the base screws and rebalance the rope when the robot is unsteady.
Once the equipment can be raised evenly, keep making little changes.
Perform lifting and translation procedures after which you gently lift the robot.

Precautions

Precautions for mechanical arm handling
The following are the safety measures for robot handling operations. Before working securely, please make sure you completely comprehend the following material:

The handling of robots and control devices must be done by individuals who have the necessary credentials for hooks, lifting operations, forklifts, and other activities. Operations handled by operators lacking the necessary competence may result in mishaps like flipping and falling.

Follow the instructions in the maintenance handbook while handling the robot and control device. Verify the weight and the steps before continuing. The robot and control device may topple or tumble during transportation if the operation cannot be completed using the prescribed technique, which might result in accidents.

Avoid harming the wire when performing handling and installation tasks. Additionally, preventative steps such as covering the wire with protective covers once the device has been assembled should be taken to prevent damage to the wiring by users, forklifts, etc.